Recent content by Appalachian Offroad

  1. A

    2012 XC250 E-start

    I apologize, the 12 was a typo, it's a 13 model.
  2. A

    2012 EC300 Brake Rotor - Where to get?

    I don't know I would call BMW exotic, at over 100,000 units a year they're pretty mainstream and still over priced. :D
  3. A

    2012 XC250 E-start

    We have one 2012 XC250 E-start left, give me call if you are in the WV area and want a good deal on a great bike. Thanks, Jesse jesse@ktm-parts.com 304-932-0437
  4. A

    2012 EC300 Brake Rotor - Where to get?

    Nice find, it looks like they only make that rotor for the front, they list a few for the rear but they crossover to the older KTM. http://www.mooseracing.com/products/?productGroupId=48568&productId=114663&yr=2010&mk=23&md=4906
  5. A

    LHRB Any ideas???????

    That was my though, thanks Stu. What's the easy way to block off the slave? I haven't measured, it seems on the rekluse setup the brake line is usually 72in, that sound about right? I will be ditching the foot lever, my right foot does not work properly due to nerve damage and I have a hard time...
  6. A

    LHRB Any ideas???????

    So dot 5 doesn't eat the seals like 3 and 4 does? My Rekluse has the adjustable slave so I really don't want to remove the rod. It would effectively just be an external adjuster without the lever correct?
  7. A

    LHRB Any ideas???????

    I just put a Rekluse in my 13 model and want to do the lhrb. my clutch mc is a mineral oil AJP. I would assume the only difference between the brake fluid and mineral oil is the seals so I could just get the brake fluid mc rebuild kit and swap it in, then get a brake line of the correct length...
  8. A

    2012 300 racing vs 2011 xcf 350 ktm suspension

    Sounds like a set of stock forks. I just sent mine out so I'll soon see what a re-valve does. Mine beat me up and liked to deflect, pulled them at about 23hrs. I would guess the fork is quite a bit stiffer on the GasGas compared to the WP stuff, mine was.
  9. A

    '12 Linkage and swing arm bearings

    It appears they are all the same part #BE25614010 for many years, pivot works sells ZFCBE-001-HKS for GasGas and also fits KTM and some Zuk.
  10. A

    noisy exhaust

    my 300 actually had a piece on the inside of the flange that wasn't fully welded. It rattled like crazy. Different pipe solved that issue.
  11. A

    Plug and play 1,200 lumen led

    Nice, is that an h4 housing?
  12. A

    P3 Carbon Fiber

    Just talked to them at the shop, all GasGas is in stock. KTM 250/300 are a day out. 350f is the only thing delayed, mainly because the molds for the new bikes with the resonance chamber were just finished.
  13. A

    P3 Carbon Fiber

    There should be little to no wait time on most everything. Some of the new stuff like Beta they may be backed up a little on because there aren't enough molds and making one piece ties a mold up for a day. Let me know what you need it for and I'll find out for sure. I think the big issue with...
  14. A

    P3 Carbon Fiber

    Not really a new product but we just wanted to get the word out that we have recently purchased P3 from Eric who will continue to make molds for us. We have our shop set up right here in WV with a few people working full time making parts to the same quality as when Eric made them. Check out our...
  15. A

    2013 300 E-Start

    No one buys 250s any more? Still one left.....
See more
Back
Top