Recent content by Gibby

Went riding yesterday started up and ran fine for about 2 miles and blahh just died. We figured it fouled the plug but when we put a new one in still no spark. After about 10 more minutes and pushing back toward the truck Tryed it again and if fired up and rode all the way back to truck turned...

Glad that I didn't back it out far enough to get spat on!! I just got my suspension tuned, revalve and resprung from Drew Smith W.E.R. I haven't had much ride time since I got it back but what little time I have had it feels nice. There is no more hard spike in the rear. Front and rear are both...

Got it. Thanks

I have a 13 xc300r with ohlins 888 shock. Does this have a high speed adjustment? There is a nut that can be backed out on the outside of the low speed compression adjuster. Some have said it is a high speed adjustment some say not, i have backed it out a couple turns and didn't loose any fluids...

2013 xc300r south alabama Oz, I see where you changed to the: main = 175 pilot = 40 needle = nedw 2nd from top slide = #7 from the 178 main, n3cj needle 3rd, 42 pilot. I have not done any head mod but I have purchased the nedw needle. I like the the power delivery with the n3cj and 178 main...

2013 xc300r south alabama 2nd jetting post, 1rst post feb,2013 Bike= 2013 xc300r 38mm as2, elevation= 0 sea level - 500ft gulf of mexico. main jet = 178 pilot jet = 42 needle = n3cj 3rd middle clip. airscrew = 1 3/4 out slide = #7 float height = 2mm above stock premix 93 octane 44:1 amsoil...

Rob, I live in south Alabama, I have a 13 xc300r, I have been haveing jetting issues also, The bike came stock with: main 175 pilot 42 needle n1ef middle clip slide #7 idle screw 2 out. When I first bought the bike it was too rich, it would foul plugs on start up every second ride, after...

Fuel hard to find. That is awesome! I have to load the bikes and drive at least 10 miles. but I have a nice 6 mile trail There woods, lots of trees, some nice woops, tight but some little opens along a powerline, very rural, deer country, I have always wanted to go to Australia, I was...

Tried out the amsoil dominator today rode about 20 miles, 2nd clip, bike felt a lot better all the way through the power curve, no hesitations, no sputter going into wot. The golden spectro was just to rich. Hey Jakobi, I guess amsoil dominator is best for me! Where in Australia do you live...

Thanks for the input, I will try amsoil dominator this weekend.

Just picked up a new XC 300R from Mort's Powersports in Mobile, Alabama. John the owner is a great guy and has been very helpful trying to help me get the bike dialed in, I have had the bike for 2 months and have put 10 hours on it. I will be riding mainly South Alabama Woods, Tight, Technical...

I guess your right stock needle needs to be trashed. Sounds like maybe I should try a nedj to start. what year is your 300 and what Ratio are you running your fuel? Thanks a lot very helpfull.

I have been reading about different needles but not sure what to try first. If I move the clip down 1 it seems to have a splatter between mid and high after running it low for a while. Fouls a plug after every 2nd ride, rain or sun mode. if I leave it in the 2nd clip down. If I run it in top...

New XC 300R :-) Just picked up a new XC 300R from Mort's Powersports in Mobile, Alabama. John the owner is a great guy and has been very helpful trying to help me get the bike dialed in, I have had the bike for 2 months and have put 10 hours on it. I will be riding mainly South Alabama Woods...

New XC 300R :-) Just picked up a new XC 300R from Mort's Powersports in Mobile, Alabama. John the owner is a great guy and has been very helpful trying to help me get the bike dialed in, I have had the bike for 2 months and have put 10 hours on it. I will be riding mainly South Alabama Woods...