Recent content by Hicksi

  1. H

    2001 GG EC300 SuperMoto (UK - Bristol)

    Hey, As the title says, up for sale is my '01 Gasser EC300 SuperMoto. The bike is in Bristol, UK. V5 document present, although its currently SORN with no MOT (expired during the build). This was always a build project for me, I never intended to ride it on the road especially after all the...
  2. H

    rear tail and brake light wiring help

    I'd Just like to +1 Dave on this thread, was going to post the same problem but using Dave's advice Tail Light now working pucka! Using the DRC LED Tail Light on my '01 EC 300 Wiring is: EC300 - DRC LED Black - Black Violet - White White - Red Working a treat, DRC Light is very bright too!
  3. H

    WTB - EC 250-300 Side Stand / Kick Stand (USA+UK)

    Hey, Looking for the side stand assembly, or just the stand, whatever you've got. Got addresses in both the UK + USA so both sellers welcome. If you could email hicksidemon@btinternet.com Cheers
  4. H

    2001 EC300 Exhaust (UK)

    Hey, As title says, got an OEM expansion chamber for sale. No dents, just needs a clean up... Open to offers. Send PM, or contact hicksidemon@btinternet.com Also selling EC plastics, see other post.
  5. H

    2001 EC Plastics (UK)

    Hey, As the title says, i have several fairing parts up for sale. Open to offers. Send a PM or, contact me @ hicksidemon@btinternet.com Also selling EC300 exhaust, check other post.
  6. H

    WTB EC250/300 Side Stand

    Hey. As above, after a side stand for my EC300. Guessing a 250 will fit also... PM me here, or email me @ hicksidemon@btinternet.com
  7. H

    CBR400 Engine Noise - Help

    Success Gentlemen! I had the time to remove the fairings on the CBR today. I used a piece of wood as a make shift stethoscope, and had a listen to the motor. The noise i could hear just wasn't coming from the motor. On further inspection of the exhaust, the sound seemed to be coming from...
  8. H

    CBR400 Engine Noise - Help

    Guys i would really like to extend my thanks to all! The input is greatly aprechiated, i have been out of the country for a while so appologies for the long delay in response time. I now have some time to spend on the bike, so ill start with the simple aspects and start to try and isolate the...
  9. H

    CBR400 Engine Noise - Help

    The CBR400 is a '95 model, its done about 39K Miles. I certainly never raced her, and the owner before me had it in the garage. Its been used for commuting and the occasional sunday razz... Thanks for pointing that out Bryan, i will check that first. Would rather replace that rather than a main...
  10. H

    CBR400 Engine Noise - Help

    Hey, From my last ride and closer inspection i've noticed the motor making this noise. http://www.youtube.com/watch?v=SE1srCq5f3A Anyone got any ideas as to what it is? I had a thought that it might be the main bearing?
  11. H

    Vapour Engine Temp and RPM Limit values?

    Hey, I've installed a Trail Tech Vapor onto my '01 EC300. I need to program the maximum temperature value and maximum RPM value in order to set the warning lights. What would be a high temperature? And what would be a red light value for the RPMs? Thanks
  12. H

    SM Conversion - 320mm Disc

    Hey Looking to kit out the '01 EC300 with a 320mm Disc, relocating the existing caliper with a bracket. Where is the best place to purchase these items? I live in the UK, but dad lives NY so can order parts from the US. Thanks
  13. H

    Exhaust seal ring?

    Hey, I noticed the notch for a seal on the exhaust manifold on my '01 EC300. Does anyone UK side know where to purchase these seals as i really need one? Is it possible to use one from another bike? Say if i went down to my local KTM dealer and bought one for the 250exc or 320exc? Thanks guys
  14. H

    Carb issues - Float bowl?

    Again, thanks for the tips... I eventually worked out the problem. And its pretty embarrasing :rolleyes: When working on the bike i had plugged up the bottom of the airboot to stop dust and what not geting in. I'd actually forgotten to remove this and it had just been sat there chokeing off...
Back
Top