Recent content by jason tati

  1. J

    2007 ec200 reed valve block

    well ive ended up scoring a cr250 reed block and fitted I think its a psr02 set of boyesen petals so far this set up using the carb and jets on the bike seems better than the new vfoce3 reed block I bought.. much smoother right through the range same top end or seems that way to me any way...
  2. J

    2007 ec200 reed valve block

    cheers husley righto mate I think I got it sorted now got a few items from ebay which may fit.. so I'm hopeing I wont need the 2nd hand part seen as the mob that sold me the p/v reckons I wont need it but I wasn't so sure
  3. J

    2007 ec200 reed valve block

    and I hear crickets..... not a very popular bike now I would think...
  4. J

    2007 ec200 reed valve block

    hey lads I'm looking for a replacement reed block for the gg ec200 2007 model.. i was reading another post which seemed to suggest that the std reed block could be upgraded and got hold of a cr250 98mod reed block same bolt pattern but no good on the fit to carb.. sent a few emails to boyesen...
  5. J

    pv breather 2007 ec200

    got 2 of these for the breathers.. http://www.ebay.com.au/itm/231787619225 2 of these for the fuel will get a stainless elbow barb for inlet and a straight barb for outlet.. http://www.ebay.com.au/itm/401130886969 and some of this for obvious reasons I would think...
  6. J

    pv breather 2007 ec200

    not a bad idea rb will be lookin for one now
  7. J

    pv breather 2007 ec200

    gday lads I'm setting up a ec200 and have never worked on a 2t I see the pv breather bolt or spigot was broken inside the hole after much much work got the broken thread out.. without removing engine from frame!!! now I see it must be from factory the hose is folded and cable tied, and after...
  8. J

    cross over for rear wheel dust seal/ wheel spacer

    cheers swazi cheers swazi will ava look when I get home
  9. J

    cross over for rear wheel dust seal/ wheel spacer

    hey lads I'm lookin for a crossover for p# 36 the stainless spacer that the dust mud seal seals onto? as I'm finding the gg ones are taking to long to get to me..
  10. J

    Credit due

    I just put an order through, jeff is super easy to deal with as per jakobi's post parts will be delivered to ya nearest dealer, they are doing stock take or something at the moment took a while to get back to me... but easy to deal with!!
  11. J

    gday from cairns, oz

    couldn't say for sure on the croc farm personaly i don't know havnt heard, but as the news had reported it close by,,, could be the hartlys creek (wonga) farm but that more than 100k away they did say it was close by must be a new addition?
  12. J

    gday from cairns, oz

    bit foolish swimming in that area there is a croc farm not far from there!! never the less yep sad state of affairs,, rumour has it she was visiting a friend who was getting ova cancer!!
  13. J

    2007 ec 200 wiring mess

    lone tree is in with the win I would reckon,, crew there ya go a little bit of info for ya will fire it up when the rain stops so could be a week away... but lonetree your right I think.. grey / yell goin in i had figured it was the horn and had connected it up but,, to be sure to be sure...
  14. J

    2007 ec 200 wiring mess

    master jakobi indicators it must be leonelli rings a bell its dark here at the moment so will ava look tomorrow fire it up hook em up and see what happens prob should have done that earlier but didn't want to short out wiring. im confident we have the solution... all bar that little yellow...
  15. J

    gday from cairns, oz

    cheers barossi have been looking through the site getting top info all round cheers shawbagga jakobi has replied to a post already.. I aint been on a site quite like it!!... im on a rc car site and fuck me for adults those guys are real children!!!
Back
Top