Recent content by modette

I have extra subframes and I don't NEED them as my 2012 got the Aluminum one for it. I can see what I have in the attic. I'd probably work you a deal. I think the 2012 and 2013 are the same from what I recall. I should ask though if you are in the US otherwise shipping be too difficult.

All these years later, and I am just now ordered the front rotor and the rear rotor and new EBC pads...LOL Moose 1711-1402 Front Moose 1711-1418 Rear (seems they have used this for a long time on EVERY bike) EBC FA185R R-Series Sintered Front EBC FA367R Rear The Front pads are the same as...

No problem...glad I could help you out with the case and what have you.

If you are in Colorado or close to Meeker, CO more specifically you can come out to a Rally we are putting on for Dual sport, Adventure, heck even dirt riders can show up as the Town is OHV friendly and routes can be accessed right from town. August 17th-20th Note you will want at least a 70...

I set 10 cards to the side just for this forum. I have a bunch of extras and not much time so I am posting 10 codes for you all. I hope it saves you all some money for Christmas. It helps Rocky Mountain adventure Riders out as if cards get used then it shows we spread the word. 25% on entire...

I made a video showing it on the bike. https://youtu.be/P6CvWpXzAiM Side by Side with OEM plastic one https://youtu.be/ltH40eGnsDE Checkpoint Off-Road: http://www.checkpointoff-road.com/store.html PART NO. 5003 Using a Matto Cycle gasket too (he has them made thicker) www.mattocycle.com

*Also a fun side note the 2000-2007 Honda XR650R Fiber's and Steel Plates fit the 2012 Gas Gas EC300. https://youtu.be/QvecUq1wHsI

You can also upload GPX files or if you have local systems that are mapped feel free to get those to us like Shapefiles we can convert it and make it usable. As for us to come to Washington, NO right now in true startup fashion we make nothing the little we get thus far goes straight to paying...

Do you mean me? My bars now are fine. I was just wondering on the bar size and what people get and what will work with a threaded insert/tapping the bar ends.

I been away from this site a long time, been busy as you can see from the below link. http://trailtaker.com/trail_systems We have mapped a lot of trails and developed a good library not only where you can download GPX files for FREE you can watch videos of the trail we map. If you have a video...

I have a 2012 EC300, US Spec so I have the Renthal Twinwall bars. Are they 1 1/8". Looking to maybe get new bars and also some Highway Dirt Bike Guards. Mainly the switch is so I can have a threaded hand guard insert which I found out the twinwalls don't allow me to tap because they have a...

So the Part's list on GoFasters.com is WRONG https://youtu.be/RRQiRQeQ7gA My Install video: https://youtu.be/JjfHFPYcsNo These fit my bike and I suspect they would fit a EC300 2014 and 2015 also and of course a 2013 as All Balls says they will. 1 - 6005-2RDQE6 (25mm ID, 47mm OD, 12mm W) 2 -...

Not sure if this fits a 2012 Gas Gas EC300 but did find a post with some information (I'm guessing I need to finally buy a caliper to take measurements) Rear Wheel - Seals 1 of each (mm) - 32x47x7, 25x42x7 Bearings - 6004-2RD x 2, 6005-2RD x 1 Front Wheel - Seals (mm) - 30x42x7 x 2 Bearings -...

Looked at SKF but had no idea what size bearings or anything I would need not to mention what seals. I guess I'll stick to the All Balls unless someone knows what part numbers to get from SKF for seals and bearings...wouldn't mind doing a video of them comparing the two brands. Yeah I have...

Well I ordered them total was $37 for front and rear with seals (I got them through Amazon sellers). I do videos so if they suck I guess they will be told that on YouTube to a lot of people...LOL I like the Clutch Cable I got for the XR650R, very well built. What would you recommend then for...