Recent content by Tom Zelko

Parting out 05 450 FSE I am parting out my 450. The thing handles great when it runs. Did I say WHEN IT ****##* RUNS! 50 marzocchi, clarke oversize tank. Selling everything except the rear ohlin, its going on my 300 EC so I have a sachs rear shock. Tom 808-372 2706

I have used every skid plate out there for GasGas Go with the mecasystem you can get them @ Cycle Pro 775-738-3276 Pipe guards, Hand guards, TM chain guides with adapters and LTR jetting kit can be purchased from Go Fasters 320-839-7143 I have found Go Fasters the best for parts. I was running 2...

In Our Riding Group There Are 2 300's, 1 07 Gasgas, 1 08 Pumpkin, 4 250's 3 Gasgas And 1 Pumkin And 4 200's, 3 Gasgas, 1 Pumkin. The 08 And 07 200 Gasgas's Run Out Of Gas When The Rest Of Us Still Have 1/3 Tank. The 04 Gasgas 200 Gets The Same Mileage As The Rest Of Us. We Are Riding At Sea...

moose skid plates They fit fine on a couple 08 250's and 07 250. You must have got the wrong one.

2007,2008 Ec 200 Gas Hog? we have 2 200's that ride with us and they are always running out of gas when the rest of us have 1/3rd. tank left?? One is a 07, and my son has an 08. We have a 07 EC300, and a 07 EC250. The rest of the bikes are pumpkins, and they get the same mileage as our 300 and...

fuel injector adj. I bought all that stuff from techno research and all it does is tell me that things are ok when they are not. We adjusted the thing by ear and it ran just a little lean then quite running again. I have owned 8 GasGas's and have to say my 05 450 has given me more troubles than...

Skid plate How can we see a picture of this skid plate? We bought 3 of the scorpion skid plates out of Canada. The front of the skid plates had to be cut to clear the pipe, but after that the things are holding on much better than anything else I have tried,(moose and flateland) It did take...

Force rad guards I got mine yesterday put them on my 08. I only had to drill out the threaded hole were they attach to the frame, took 1 minute with 1/4'' drill bit and they fit awesome. It is nice to see someone takes pride in there work like The force company!! The top bolt I used the stock...

High elevation jetting Thanks for the info on jetting. Does anyone know about jetting a 08 300 in elevation of 8,000 - 10,000 ?? Thanks Tom

skid plate well, I ordered the moose plate, and the scorpion plate. After looking at how the scorpion plate is made it seems to be the best by far. The problem is the scorpion plate will not be out for a couple weeks and we have 3 08's that need plates today. The scorpion plates are made in...

skid plates thanks for all the info, this forum is great for this, I ordered the moose plates yesterday and am getting info on all the other skid plates. I will do the test and let everyone know whats up. In Hawaii we have plenty of rocky river beds. Thanks Tom 07-300 and a 08-300(in box still)

Skid plate I tried the hyde and I did'nt get a hole in the case, but my frame was bent up pretty bad after taking it off. and my pipe burned out a nice little section out of it, and it was like grinding on my skateboard on a half pipe when I would go over a big log when it was wet. No thanks...

Does anyone know who makes a skid plates that is any good for Gasgas?? 1) Flatland. stop making them. Theres was the best except for the brackets 2) CRD. not importing any more, besides they were way to thin 3) Hyde. well they are plastic, enough said 4) Force. out of Australia nice radiator...

300 set up bark busters, skid plate, tm chain guide, radiator guards, and leave the dual mapping on rain. The tires of your choice and the only problem you may have is overheating if you clutch alot in really tight slow areas. I have had 5 and love these bikes. I am checking on the force rad...

Force rad guards were do you get these things?? I had to cut and re weld my flatland rad guards for my 07's The 250 and 300 are the same but the 200's are different, I should of checked since I templeted from the 07 250. Did Flatland make the change for the 08 bikes? Do the force need to be...