Recent content by yowie05

The Fmf pipe for 07 will not fit years before that. I bought a job lot of 07 parts for my 04 and the pipe does not fit. Even the silencer will not fit as the subframe mounts are different.

Hey guys I have an 04 model I?m looking to update the look. I already have a 2011 rear subframe and an 09 airbox but the airbox does not marry up to the left side cover from 2011. I need the rear part of a 2010/2011 airbox or the whole thing and a newer seat as well not sure if an 07-09 would...

Took my bike in to dealer 4 weeks ago tomorrow. Still no word on when I'll be getting it back. If you can get the nut yaself I would do that.

well they dont have a black knob. they are the same as these https://www.ebay.com/itm/2006-06-Kawasaki-KX450F-KX-450-Front-Wheel-Fork-Shock-Leg-Tubes-/263863429748

The online are off an 06 kx450 other than that no idea. I had the mazocchis rebuilt about 12 months ago but not change the springs rate or revalved to my weight. My plan is to now do that but wondering whether to do it to the ohlins or the zoks.

What is excess bleed and using a crossover? Also clamp shim. Im new to working on suspension. I've replaced the oil to spec lvls but havnt gone any further in than that. I need to change the springs in the ohlins forks as they are not for my weight. I'm 65kg so even if they standard weight...

sweet as guys thx. good idea RB

Needing a new set of sprockets an was on the dirttricks website and they list Gas Gas: ?99-Current 200/250/300/400/450/515 Sherco: ?04-?12 4.5i/5.1i ?11-Current 250/300 SC-R ?17-Current 450 SC-F as being the same sprocket. is anyone able to confirm this? my nearest gasgas dealer that...

Funny you say a top heavy 450. book wieght on the 04 EC300 is 109kg and the book weight on the 06 KX450 is 104kg. anyway Ive done the swap. Ive got everything on softest setting and its actually pretty reasonable. id say the spring is too heavey for my wight as im only 65kg so am looking to get...

hi guy just wondering if im doing this JD database correct. i think i am because on the needle profile I can see the 3 tapers or just the single taper. my bike is an 04 ec300 currently running NECJ clip 1 42 pilot 175 main. i feel its too lean but the bike runs well. on reading a lot of older...

hi guys, I have an '04 EC300 with the 45mm Mazzochi forks. 12 months ago i had them rebuilt and they are leaking already. Anyway i have an '06 KX450 with Ohlins 48mm forks and an original GG triple clamp set to accomodate the 48mm forks. Considering its not going to cost anything except...

Just what I was thinking. Something similar thanks.

Hey guys, wondering what you all use for the plugs in the tank that the radiator side plates screw into on older models (04). I've got 1 that is non existent any more and a couple others that are nearly gone. Besides gluing a piece of dowel or similar in there I'm at a loss. TIA

more wicked input guys thx. as stated b4, going to run it as a 300 for a couple months to get the feel and my fitness back up, then will swap to a 250 and see how i go. i know i dont use the clutch much atm so i may have a bit of fun with that when i do the changeover. im not much of an open...

Awesome stuff guys thanks heaps for the input. Great points Jakobi thx. By the sounds of it I really should leave it as a 300 due to my riding style and terrain that I like, plus being an older(read unfit/lazy) rider. Think I'll get it running again as a 300 and after a few rides I might drop it...