2011 Footpegs

[Wbdisco]

Any ideas if the Rieju pegs will fit the old gasser? I looking for an upgrade over the stockers.

 

[Jacob 'Berg]

YZ footpegs will fit the 2011 gassers. You may have to do a little research and/or cross reference part # from aftermarket suppliers.

 

[Wbdisco]

I will check that out, I was on CPD is why I was asking about the Rieju ones. They looked pretty nice.

 

[SS109]

I think pegs are the same as Rieju. Matter of fact, that's how CPD lists them as being a direct fit.

That said, AS3 has a couple of nice options for pegs: https://www.as3performance.com/collections/gas-gas-ec-250-enduro-parts/year-2011

IMS did offer their Super Stock, Pro Series, Core Enduro, and Core MX pegs for our Gassers but don't know if they still do. I run the IMS Pro Series pegs myself.

On CPD it shows some options to be:
https://cpd.direct/collections/gasgas/products/punk-steel-footpegs-by-s3
https://cpd.direct/collections/gasgas/products/hard-rock-footpegs-by-s3
https://cpd.direct/collections/gasgas/products/footrests-hard-rock-curve-deep-low-s3
https://cpd.direct/collections/gasgas/products/s3-footpegs-steel-enduro-esk-569-t

 

[gasgasman]

The '18 on up GasGas / RIEJUs use the 2016 KTM pegs.

 

[SS109]

CPD lists the S3 Hardrock pegs as fitting the following bikes. If this is accurate, it's a good cross reference.

RIEJU (19-Up) MR, MR Pro, MR Racing
GasGas (98-18) EC, EC F, MC
Husqvarna - (15-Up) TC 65
KTM - (92-16) EXC, EXC-F, XC, XC-F, SX, SX-F, XCW-F
Husaberg (09-14) FC
Montesa (14-Up) 4Ride (Not 4RT)
Beta (06-19) RR, RR 2T, RS 4T, RR 4T, RR-S 4T, XTrainer
Fantic (16-Up) XE, XEF, XX, XXF

 

[Wbdisco]

If that is correct it will make it a lot easier to find some. Thanks.

 

[Wbdisco]

Anyone running the high dollar titanium?s? I like the stock Rieju pegs, seem simple and tough, still expensive. https://cpd.direct/collections/cont...el-factory-racing-hard-enduro-foot-pegs-rieju

I am not sure I want the pegs with stainless individual screws, seems like I could break and strip them out.

 

[Anders]

I am not sure I want the pegs with stainless individual screws, seems like I could break and strip them out.

I have used both Talon and S3 pegs with stainless grub screws. Works very vell for me. You'll have to replace the screws from time to time as the pegs becomes slippeey when the screws are worn.

Sent fra min YAL-L21 via Tapatalk

 

[Wbdisco]

Any trouble getting the screws out? I know that dissimilar metals can corrode.

 

[Anders]

I have never had any problems getting them out.

Sent fra min YAL-L21 via Tapatalk

 

[Wbdisco]

That?s good to know, I hate drilling out screws. Stainless is a real bugger to drill.

 

[Wbdisco]

FYI, Yamaha Carapaks stainless footpegs fit my 2011. These things are awesome. 5mm back and 5mm down. They feel great and definitely an improvement from my original ones.