rear wheel bearing shim spacer dimensions?

M

mattlloyd50

New member
hi does anyone know the dimensions of the spacer that fits between the two wheel bearings on the sprocket side. its like a big washer. i have ordered one but need it before the two week delivery date.
thanks for any info. matt
 
mattlloyd50 said:
sorry. its a gas gas ec250 with the standard wheels with 2 6004 bearings and 1 6005.
thanks
Click to expand...


I have an old wheel that i could knock the bearings out and measure up but i could not do it until the morn (Fri) is that too late

It is off a 98 GG not sure if it is the same as yours.

My other wheels are talon hubs which i suspect will be different.
 
no thats not too late im grateful that you are willing to do this.
thanks very much.
would you like to sell the spacer and the circlip from the other end?
 
I just ordered a 4mm wider inner bearing for mine and shaved 1mm off the outer spacer. I even put the 7mm seal back in and it seemed to work, even though I had a 6mm one for it.
 
FYI-The inner spacer keeps the side pre-load off the inner bearing race when you tighten the axle nut.
 
I've just had some new spacers turn up that I had on back order. They are very different to the old. They are a little thicker, have a smaller OD - i.e would not fill the hub and have an odd chamfer on the outside that I can see no purpose for. Dealer swears these are what the factory are supplying now

Can anyone offer any advice?
Have they changed a lot?
 
Do you mean like this http://www.gasgasrider.org/forum/showthread.php?t=2566 ?
I had the shop rebuild my rear wheel with the allballs kit, they must have thrown out the spacer, and just run the bearings, it probably lasted 200 odd km before the sprocket side spacer broke the center of the bearing and ceased onto the spacer. Made a rather strange noise after that....haha. I was lucky it lasted that long though, because it happened after a ride where there were sections that were tapped in 6th gear over sandy whoops, would not have been cool for them to fail then.
The shop replaced them at their cost, with the spacer :) no problems since.
 
Noobi,

No not like that. The ones in the link look like I was expecting. These things are weird.

By the way I don't think Allballs supply the spacer. Never been one when I've bought their kits.
 
iancp5 said:
Noobi,

No not like that. The ones in the link look like I was expecting. These things are weird.

By the way I don't think Allballs supply the spacer. Never been one when I've bought their kits.
Click to expand...

Oh ok, I wonder what the deal with that is, if you cant see a logical way that it fits they may have stuffed something up....


Thats correct, allballs do not supply the spacer so make sure to keep it!!!, and tell the shop that its there so they dont loose it. Not telling you ian, just a general warning
 
Matt

Circlip in the post to you.

Thrown out to all Does the talon hubs have this kind of set up?

All Balls ? Are they any good I bought a swinging arm kit and thought the quality was fairly pants.
 
Thrown out to all Does the talon hubs have this kind of set up?
Click to expand...

From what I have read the Talon hubs also have a dual bearing setup on the drive side. I have no idea if it's 2 seperate bearings like the GG or a dual row bearing which to me makes more sense.
 
anybody have the measurements?

so back to the original question: (dimensions of the spacer)
i would like to also know what the dimensions are, but at least the thickness(distance between the bearings). mine is worn and i would like to make a new one from stainless.
thanks
ken
 
I have a new on e on the way. I ll get some measurements from the new one before I install it. Can you make a small run of them?
 
You must log in or register to reply here.

Similar threads

N
2005 EC200 Small End Bearing
Replies
3
Views
2K
Anders
Anders
B
Front wheel bearing for 250 Pampera mk3 (2002)
Replies
0
Views
4K
Blambo
B
V
Clutch shim?
Replies
1
Views
14K
Gasser Nate
Gasser Nate
B
2018 XC300 Linkage slop after complete rebuild - driving me nuts!
Replies
7
Views
4K
(F5)
(F5)
I
Rear wheel bearings
Replies
4
Views
3K
Hooligan
H
Back
Top