What did you do to your Gas Gas today?

[desertgasser300]

New seat cover......never mind the messy garage, its to hot to get in there and give it a proper organizing!

 

[Phaeton]

That came out nice. Not sure about the white though!

 

[desertgasser300]

That came out nice. Not sure about the white though!

Ill deal with dirty white then the faded red that turned pink I had before. We dont have alot of mud here any how.

 

[bowhunter007]

I'm diggin' the white. It's like driving a beat up, ugly truck...can't see it, when you're behind the wheel.

 

[Todd5774]

Fitted new tyres and moouses, rear wheel bearings, new chain and sprockets, new gear lever, BRP chain guide.

Now Sunday's job is to convert the engine back to a 300 from the 250, want abit more torque again for the sloppy winter mud..

 

[shang]

New seat cover......never mind the messy garage, its to hot to get in there and give it a proper organizing!

I love the white on the seat cover!

Did you remove the frame guards? I really like how it looks without it, but didn't want to wear the paint on the frame.

 

[desertgasser300]

I love the white on the seat cover!

Did you remove the frame guards? I really like how it looks without it, but didn't want to wear the paint on the frame.

The 12's came with a thick rubbery frame guard that was glued on, when they wore off i just replaced with grip tape. I still have the oem on the right side.

 

[Tigger52]

Had my 2002 EC300 re-jetted and set up by Jack Lee at John Lee M/C's in the UK. He recommended running the pre mix at 80-1 instead of the 50-1 I'd been using - runs like a scalded cat now, starts instantly, idles perfectly and sounds really crisp.
Still slightly uncomfortable with the new pre mix ratio, but Jack's got loads of GG experience so I'll trust him and see what happens?

 

[Jim Cook]

Had my 2002 EC300 re-jetted and set up by Jack Lee at John Lee M/C's in the UK. He recommended running the pre mix at 80-1 instead of the 50-1 I'd been using - runs like a scalded cat now, starts instantly, idles perfectly and sounds really crisp.
Still slightly uncomfortable with the new pre mix ratio, but Jack's got loads of GG experience so I'll trust him and see what happens?

What premix oil are you using at 80/1?

 

[Rick]

Ill deal with dirty white then the faded red that turned pink I had before. We dont have alot of mud here any how.

A little Shout stain remover and it's all good! Looks good!

 

[Tigger52]

Using Putoline MX5 semi synthetic - fingers crossed!

 

[Jim Cook]

Using Putoline MX5 semi synthetic - fingers crossed!

Keep us posted on the results.

 

[paulos]

Nothing too exciting, put a sticker kit on, not flash, but better than the previous bare plastics

 

[Jim Cook]

Nothing too exciting, put a sticker kit on, not flash, but better than the previous bare plastics

That looks good!

 

[Phaeton]

Rekluse Clutch, Brake Bushing, Brake Clevis, Sent pipe out to Pacific Crest Pipe Repair and added P3 Pipe guard, Motion Pro Throttle Cable, New Shifter, Seat Cover and I made a new seat hold down washer.

 

[desertgasser300]

Nothing too exciting, put a sticker kit on, not flash, but better than the previous bare plastics

Very clean look, good job.

 

[Jakobi]

Nice ride Phaeton. Bit of bling in that bike. I notice a newer model cylinder and S3 head on her too. Brap brap!

 

[Phaeton]

Yes the bike was converted to a 300 just before I bought it.

 

[Darrendeep6]

Yes the bike was converted to a 300 just before I bought it.

Very nice ride mister

 

[paulos]

Went and got it dirty. I know you're only supposed to change one thing at a time, therefore i can't tell for sure whether it was the sticker kit or my new flash gas gas riding pants (sorry no pics of the pants), but average speed was up 15% and torque/hillclimbing ability improved by approximately 8.5%